lil SOLID Ez is a simple to use one-piece device to enjoy the best tobacco heating experience without the hassle of fire, ash and smoke.
It heats tobacco from the inside by a stainless-steel pin for consistent tobacco experiences.
With lil SOLID Ez you will enjoy:

• Consistent heated tobacco experiences, with 3 back-to-back consecutive uses
• Up to 25 experiences on a single charge*
• 5 minutes duration of one session

Available in 5 new colours:  white, blue, mint, rose gold and black. Learn more

*Subject to battery performance degradation and conditions of use.

lil SOLID Ez and lil SOLID 2.0 - are both alternatives to continued smoking. lil™ SOLID Ez is the next generation of lil™ SOLID 2.0 all-in-one tobacco heating device introduced by IQOS™

What’s new:

1. Heating technology – resistive heating with a pin
2. New device finishing – glossy finish
3. New 5 colours: rose gold, mint, white, black and blue
4. Smaller & lighter – 78.9 gr for lil SOLID Ez vs 98.8 gr for lil SOLID 2.0
5. 4 new cap accessories for personalization: Stellar rose, stellar amber, stellar blue and stellar back. Now with a total portfolio of 9 coloured caps
6. New additional cleaning tool – lil SOLID Cleaner Pro, for cleaning the cap and around the pin. Sold separately.

Both devices – lil SOLID Ez and IQOS ORIGINALS - are tobacco heating systems and heat tobacco from inside. However, there are some differences: 

The serial number of lil SOLID Ez is displayed under the cap of the device.

You receive the new device in sleep mode. To wake up the device, press the button for 2 seconds or connect the charger to the charging port.
Once the device is activated, the Status LED blinks in ice blue for one second and vibration occurs twice, simultaneously.
We recommend to fully charge your new Iil SOLID Ez device with the supplied AC Power Adaptor before using it. It takes up to 2 hours. 

Slide and open the cover of the stick insertion part at the top of the device and insert a tobacco stick with the tobacco part of the stick facing down.
Press the stick until it touches the bottom of the stick insertion part. 

To start your device, press the button for 2 seconds until vibration occurs.

Preheating will last for about 25 seconds. The duration time of the preheating process can vary according to the use environment.
When the preheating process ends, the Status LED lights illuminate, and vibration occurs simultaneously. The stick is ready for use.
Use: you have up to 14 experiences or 5 minutes, whichever comes first.

To signal the last 30 seconds of the session or the last 3 experiences, whichever comes first, the device will vibrate once and the Status LED will blink in ice blue until the end of the session.
At the end of the session, the Status LED and the device turn off automatically. You do not need to press the Button.

Remove the tobacco stick after the end of the experience:
Rotate the stick to one direction 3 times or more and pull the stick out of the device. 

Close the cover of the device to prevent any foreign particles from entering.

You may use the device up to 3 consecutive times without waiting time.
After 3 consecutive uses (within 18 minutes) the device will cool down automatically. Please wait. It will take 3,5 minutes before you can use another tobacco stick.

To check the charge level of lil SOLID Ez, short press the button or plug the device in a power outlet using the supplied USB Cable and AC Power Adaptor.
The Status LED light will indicate the current charge level of your device.
 

Although Iil™ SOLID device does not require a full charge to work, we recommend to fully charge it before the first use.

To reset your lil SOLID Ez, press the button for 8 seconds, even if vibration occurs within 2 seconds. The State LED will blink twice in red, orange, ice blue and blue, sequentially. 

The device is completely reset when the State LED lights blinks in ice blue for 1 second, and vibration occurs twice, simultaneously.

It is important to keep your device clean from any foreign particles, remnants or dust. For this, please, keep the lid closed at any time after the use.

For optimal experience, clean your device after every 20 uses.

You can clean your lil SOLID Ez in three ways: with a Dual Cleaner (comes with the device), by cleaning with heat* or with a lil SOLID Cleaner Pro (sold separately) 

Cleaning with the Dual Cleaner:
To use the Cleaning Wiper, gently snap open the side with the ⊙  (circle) mark. 
To use the Cleaning Brush, gently snap open the side with the  (multiple dots) mark.

Remove the cap from the cooled device and insert the Cleaning Wiper into the heating chamber and clean by spinning the wiper.
Insert the Cleaning Brush into the heating chamber and clean by spinning the brush.

Cleaning with Heat*:
To clean with heat, quickly press the button 5 times (within 2 seconds).  The State LED will blink orange for 90 seconds and the cleaning process happens automatically
When the cleaning process ends, the State LED automatically goes OFF, and vibration occurs 2 times

* Cleaning with heat means heating the remnants stuck to the heater. The heater can get very hot, so do not let anything come into contact with the heater during or immediately after cleaning with heat.

Cleaning with lil SOLID Cleaner Pro:
This new cleaning tool is efficient to remove hard tobacco residue that cumulate around the pin and inside the cap
It also allows to restore the delivery of aerosol like a new device. 

Use the cleaning wiper (the side with the “hole”) to clean around the pin:
1.    remove the cap
2.    insert the cleaning wiper in the heating chamber
3.    rotate several times to remove the crust.

Use the cleaning “brush” (the side with the protruding pin) to clean the cap: 
1.    insert the cleaning tool from the bottom of the cap
2.    rotate several times

To reduce residual tobacco after removing hard particles, use the cleaning sticks.

The lingering smell most probably comes from the non-regular or non-thorough cleaning. We recommend cleaning the device on a regular basis.

If you continue to use the device without removing the debris or remnants, the device can heat up the remnants, which can produce the lingering smell. Learn more

Solid red light for 2 sec with two vibrations -> low battery
Please charge your device

Red light blinks 5 times -> device malfunciton
Reset the device by pressing the button for 8 seconds, even if vibration occurs within 2 seconds. 

Orange light blinks 3 times -> device needs to cool down or exceeds operating temperature range
After 3 consecutive uses (within 18 minutes) - an orange light indicates that the device needs to cool down. The device will be put in the cool down mode automatically. Please wait. It will take 3,5 minutes before you can use another stick.

It could also indicate that the temperature has gone beyond the operating temperature 0~40℃. 

Orange light blinks 2 times -> liquid ingression
Please do not use the device and dry it until the light stops blinking.
If the light does not stop blinking, please, contact us at Customer Support Center [1800883858] or visit us at the nearest IQOS store. 

Blinking green light and device not responding -> device in updating mode
To interrupt the update process, disconnect the device from the power source

Charging lights: 

If you have not used the device for a long period of time, please ensure there is no visible damage present and then, try to charge it fully before attempting to turn it on. 

To conserve battery life, the device will return to sleep mode: 
1.    if it is not charged for 24 hours when the Status LED light is red
2.    if it is not used for 7 days when the Status LED light is orange, ice blue, or blue

Please note, when you start charging the battery after a long period of inactivity, i.e. when your battery has been completely depleted, the charging lights may not appear right away. This is a normal process. 

If the charging does not happen, please, contact our Customer Support via:

• phone: 1800883858
• e-mail: [email protected]
   

For optimal charge, use a supplied AC Power Adaptor and Charging cable.
Please ensure you use the right charging method. We recommend charging only with the USB Cable and AC Power Adaptor designed for lil™ SOLID. Only 5V 2A chargers will support optimal charging.
If you use other types of chargers, such as smartphone chargers, car phone chargers, or portable power banks, may cause low charge efficiency or reduced battery life.

Foreign particles may cause poor connectivity between the device and the AC Power Adaptor. To ensure the connectivity between the USB connections, please, ensure that they are clean both on the device and the AC Power Adaptor. Learn more

If you experience that you only get a little bit of aerosol compared to your previous experiences, please ensure you check the following:

•    Check if there are any remnants inside the stick insertion part. Remove the remnants by pulling the cap out of the device, install the cap back and try the new stick.
•    You allow the device to pre-heat for about 25 seconds prior to using Learn more
•    You clean your lil™ SOLID Ez regularly (every 20 sticks) Learn more
•    You pause between uses to allow the pin to properly heat the tobacco and generate aerosol

You can also bring your Iil SOLID Ez into your nearest IQOS store for a free Complete Service periodically. Learn more on iqos.com

A comprehensive professional lil device maintenance service performed in IQOS store by our experts. Every check-up is carried out to help you to keep the lil device in optimal condition for longer and to ensure a satisfying lil experience. This service is free of charge. What services are included Complete service? 

Yes, you can still get support, even if the device is discontinued, according to the warranty terms and local regulations.
Also, replacement of device will still be available if the device is still under warranty. 

You can still purchase the accessories for Iil SOLID 2.0 Learn more

lil SOLID Ez is priced at RM99.

Yes, you can order via IQOS hotline number at 1800 88 3858.

Yes, you can replace your faulty registered device as long it is within the 12 months warranty period.